For next day job on the same lease. Dispatch told me to drop off my shower for tomorrow’s job that helps pull in the shower less hazardous

I went to location to change flat tire when I got to location supervisor line me up where to park my pick up,and caution tape the area and safety huddle go to work

“Let me see your hands” before any movement was used by third party.

Real rocky terrain And bushy tripping hazards clean area before work

Doing the operation, we were pumping water everything was going well, and after that we start pumping acid like five minutes later I saw the pump start leaking. I’ll let my supervisor know and we
stop pumping we got together and we start pumping water to flush the line. We fix the problem and then we can continue with the operation and after that, we got the job done safe

It was hot pumper help pic to put the acid hose

After the job we lived the location clean pick up all the trash always practice housekeeping and all locations be safe and drink plenty of water

2 transports taking turns to look for leaks because it’s to hot

Our safety reminded me to put both of the wheel chocks down not only one

Aera safety rep did on audit and coached me on chain placement from truck to trailer. I told him I've didn't know about crossing the chains and he responded that it was corrected and it was a
coaching opportunity

After we finish the job. We unhook everything and we were getting ready to leave and I look at the well and I see a little leak from the casing so I let my supervisor know he made some calls they came
in and fix the problem and everything. Got done safe.

It was 106 out side so told transport to go in side the truck to cool off

As we arrived on location I scan the location so went we finish the job, try to leave location as clean as possible

Myself and coworkers we were impact globes for the job wile working rigging up or rigging down

Myself and coworkers we were impact globes for the job wile working rigging up or rigging down

While working at thums island (White). I started sweating profusely and feeling ill. EE Shadowing me told me to grab water and get in pickup to cool down. Temps were only in the 80's but high humidity
got me over heated

Face shield was properly worn while hammering a small wing.

Turn the operation we are start pumping we were pumping release water and I see a little leak so I let my pump that we had a little leak going on. We fix the problem and we got able to finish the job.
We had a problem nice and safe

After I hooked up suction hose to pump transport, I opened hand flapper valve and felt it filling so I went and checked what fluid was open and it was the hcl/hf so I asked why it was open and he
didn't even realize he drove to field like that. So I told him we should tighten up hammer union and prime up down hole pumping ammonium chloride. He said no and proceeded priming up with acid after
he primed it and sprayed acid around fittings on well head I had to pour bottled water before I winged up hammer union

After I hooked up suction hose to pump transport, I opened hand flapper valve and felt it filling so I went and checked what fluid was open and it was the hcl/hf so I asked why it was open and he
didn't even realize he drove to field like that. So I told him we should tighten up hammer union and prime up down hole pumping ammonium chloride. He said no and proceeded priming up with acid after
he primed it and sprayed acid around fittings on well head I had to pour bottled water before I winged up hammer union

While completing jsa and customers permit, EE Pulled in and spotted pump before I was able to sniff the well

3rd party vehicle was backing with no spotter, stopped him and assisted with spotting.

Doing the operation a MTS employees. They were using the right tools and wearing the chemical suit, it was a great communication with the supervisor and a pump operator and being say the job got done
safety

We was doing a CTU with GPS at Crimson Lost Hills and we did not have a port’ y “” party and we have to drive like a mile away,,, not good,,

A lot of traffic people on phone

Chemical suit was completely on when handling chemical discharge cap, along with face shield being down. Great job.

As we rig up to the well I observed my coworkers that they were using face shield properly hammering high pressure unions or connecting or disconnecting suction hoses

Had to you my heat glove because pipe was hot

Going to be 104 told transport to drink a lot of water

Working on second well, I see my coworker not wearing the impact gloves, AERA wants us to be wearing gloves all the time.

Having a safety meeting, I noticed that two of my co-workers didn’t have a H2S monitor in front of the shirt, I have tell them to put it in front.

Working at Aera energy belridge please keep location the way we found make sure you do housekeeping all the time be safe

Person Safely used 3 points of contact when climbing stairs

Checking on next location, and taking short cuts I was walking on uneven walking surfaces and rocks , then I decide to walk on the road

Wild pressure testing it was a man walking closer and I have to stop the pumper until the walking man was in good distance

Before start working on the trailer make sure I have my Ppe on make sure the trailer chucks blocks be safe

Everyone was wearing there ppe

Wore all appropriate attire while pumping chemicals

Correctly secured tools and equipment prior to traveling

Before job started cones tape and signs were up. I set up eye station but forgot to test. After the safety meeting it was brought to my attention, I tested eye wash and shower before job started.

Went operator used the hammer please stay away try to avoid to get hurt be safe

Seen every body in there proper PPE for job tasks

Working at freeman island we have hoses everywhere please look you step be safe

Seeing everybody with proper PPEN paperwork and all cones out and shocks jobsite luck safe

Used the right ppe always is a good safety matter keep used be safe

Seen a ploy E wear an H2 S monitor within breathing area

Ball gun didn’t work had to do it manually told pic

Used the chemical ppe is dangerous trying to not work hard and take care you self drinking plenty of water stay cool

As we rigging up to the well before hammering the unions we make sure to put face shield down to avoid getting foreign objects on the eyes

Doing a rig wash and let the guys know to drink a lot of water because they really don’t use chemical suit

One of the guys for gps was walking backwards and i talk to him about it told him he Might trip and fall

PIC successfully give instructions on how to get to location and actually place cons to direct personal to location good job

Made sure all monitors were up to date and bump tested

Working at Aera today after the job everyone clean the location job MTS crew keep do it a housekeeping

One person at job site made sure every monitor on location was up to date and calibrated

As we rigging. Up to the well I observed my coworkers that they wered all the ppe that we need to perform the job and finish the job safe and sane

It’s hit the 90s pic was Reminding transport to drink water

During the job pic and mi properly wear safety globes for the job and the rest of the ppe

Start getting hot please drink plenty of fluids trying to avoid energy drinks be safe

Need a clicker for the gate on pier g

There was hoses on the ground so we talked about it in the meeting

Need clicker for crc

As always PIC guide us all, give us a good direction ,on how to get to the well or location, good management

Went we arrived location is clean so went we finish the job we left location clean make sure everyone does housekeeping all the time

Today is hot weather on los angeles please drink plenty of water be safe

Pumper didn’t put his wheel chocks I let him know

Mi and the pic we successfully wear proper ppe during the job ha hard hat, safety glasses and proper globes for the job

Uneven surfaces pic I said talked about it on safety meeting

Got to location and the well had a pin hole so we could not do it let pic know

Today raining so much we used extra carful to spot the trucks on location and walking on surface MTS crew be safe all the time

During safety meeting, pic successfully talk about slips, trips and falls because of the mudy location ,he talked about not to walk back wards, finish job with no insident

Starting the day with the safety meeting, We talk about first day of the week and the end of the month so we talk about do everything right and go home safely

Mario had the Chemical suit and we all where keeping a eye on him since he don’t really use it

This is a CRC THUMS injector acid dump and I like the way they have set this up two Wells close together we don’t have to move the pump. We did it easy and safely

I see my coworkers, start going down in the cellur with out quad monitor , I have to stop doing whatever I was doing and walk with the quad monitor while he was coming down , We all need to have quad
monitors

Started raining so we talked about it in the safety meeting to be safe

Told everyone to drink a lot of water is already getting hot out here

Everyone at the job had all ppe on we all check h2s Monitor was up-to-date

Used the chemical ppe at80 temperature is hot so please drink plenty of water be safe MTS crew

Tag on one of the backers was duty so I replaced it , with a new one

We have a cables and hoses/iron on location so we put cones on top of cables to make sure nobody falls good safety call good job MTS crew

Ground was uneven so pic let’s us know to watch foot steps

This was on Saturday working on Berry petroleum we had to go load some water lease water to take it to well 32–13 and when we was loading water I didn’t see no water leaking but it was H2 S
around that area so what we did , is to stay up wind and load up the water that way

A lot of houses on the ground and we talk about it on the meeting

On this day the 12th we was working on the producers and I was working on 301 truck and we was ready to rig up and the real to pull the house out, was stuck and I wasn’t able to pull it out I got
help second person we wasn’t able to pull it and then we got the third person and we did pull it out with the three guys , after that is being ok

Safety first,, Would be the 937NR -18 Anguid did the long estrian and short est string and we have a safety meeting in the morning and we talk about start the week safely and finish it safely and we
did we start the job and finish the job and go home safely

whoever loaded the trucks loaded them wrong and I let my pic know

There was a lot of traffic on the way to the job site construction so will be late let my pic May

Working at Aera today I see MTS operator went used the hammer he put the faceshell down and everyone stays away good job safe always

Need spotter al the time you move a truck yes to be safe keep implementing safe

Went someone used the hammer they used faceshild down and the other estay away good job always be safe

During pumping I noticed a leak at the well I let the pic now, switch over to water fixed the problem and continue

Working on this weather watch you step because ground is not level on location is full of water be safe

Moving out the pump off location went is muddy we need to put more attention so used two grounds spotless is always safe good job MTS crew

PIC on safety meeting talk about slips trips and falls, he talked about not to walk back wards because the location was muddy

After rain from yesterday still muddy so stay alert look you step go around off mud areas be safe

PIC on safety meeting talk about slips, trips and falls, because of the rain on location, talked about not to walk back wards, to be aware of your seround, to watch your step

I was doing my pre trip and when I turn the truck on my coolant was leaking so I called my pic Randy so we Traded to a different truck

Working today at cat canyon santa maria Idriven to the hills thanks pic to put the cones to diretions to the well that is safely

Working on fog day is hard to get to location but pic make it easier he put MTS cones by location entry be safe

Going to Job site PIC successfully notified us no to go through a street witch there is a tide turn, good job by the PIC

Lot of hoses on the ground wach out for ur steps

Broken equipment, pressure gauge was broken I called the operator and gave me a new one to replace the broken one, always reported it

Walking down the stairs with tools on hands,, is not good idea we need to have 3 point contact,,

We working on tide location today so to turnaround the truck I used mi spotted yes to be safe

Pumping water through coil tubing I noticed that it started leaking from one of the connection of the coil unit I stop they fixed the problem and we continue the job

There’s a lot of hoes on the ground see we told everyone to watch there foot steps

Working on this weather we need to look steps looks for on void the slippery/strip and falls be safe

There was a lot of hoses on the ground so we put cones on the ground to make sure we don’t trip over them

We got on the island chaffee, that was our destination, the island is full of people working on rigs, it's really restricted area to drive, not to match of space, but we de it Good job

We got on the island chaffee, that was our destination, the island is full of people working on rigs, it's really restricted area to drive, not to match of space, but we de it Good job

I observed my coworker driving on to the bartch on reverse, the bartch attendance yes give him directions and put the truck right on the spot good job

I observed my coworker driving on to the bartch on reverse, the bartch attendance yes give him directions and put the truck right on the spot good job

A lot of hoses on the ground we talked about it in the safety meeting to watch out

Driving on elk hills and respect the speed limit is a good safe job always put attention

I went on a road call to south bel ridge and when I got to location I park my pick up back ward and I forget to turn off the engine and put the safety cone on top of the hood Mts pic told me that
but they were Done working

testing from Chris at Marcom on live

this is a live test from Chris at Marcom

Pis on safety meeting talk about the job, about slips, trips , and falls , hoses , cables on the ground, not to walk back words,

Good job MTS crew clean the location after the job Nice housekeeping working together all way

When we were doing the three wells our pump started leaking so I told the pump operator to shut down and start pumping and let them know what was going on so Juan Alvarez talk to John and he had a
change pump trucks and finish the wells

Rigging down,, the job went fine from the start to the end but after rig down and turn the well to the company operator. He was ready to open the flow line and I start smelling some H2S And we see the
water and acid start coming up from ground, so we call operator to come in and see it.

Backing up the truck on tide location we make good communication using ground guide pic/ drive good job

Spotting equipment. On this job it was a Lot of equipment around the wellhead like pipes vans half thanks and like six of those Baker thanks , in order for us to do the well we have to use two or
three hoses but then we found out that there was a vacuum truck that we had to move out of the way, so call some one to move it, so they did and was able to pump the job

Communication,, this was a Pigging job , But before we do the pig and they want us to pressure test a 50 footer 16 inches pipe so David he communicate with me the day before and that day of the job.

Driving to location,, On this job it was at 5:30 AM so we have to be there by five and it was too dark so I make my truck wait on the main road I went to look for the well and come back and get the
truck in by then it was a little better clear.

On this job we have to go up on the hill and passing the Rig underneath the guidelines, on a narrow road we did it going up and down safely.

I observed my coworker doing t right way walking up and down the stairs , using three point contact good job

We are doing three wells today and everything went fine and smoothly the whole crew working safely may all have a wonderful weekend

Ringing up these morning, I observe my co worker successfully puting he's face shield down every time that he was hammering hose unions

Transport for got to put if ground so we let him know

After the job all crew make a good housekeeping on location no trash living good job MTS crew

Everyone had there mask on and we stayed 6 feet apart

Used the chemical suit and all ppe is making the body more hot that normal so take care you self drinking plenty of water be safe

As we were hammering hose unions, we should, hammer time, alert everyone the job that it was about to take place that way everyone is safe and healthy

When I did my walk around I seen the well leaking water so I told pumper to stop and call the rig crew to fix it and they did

Location is not level and had pipe tools all over the place so look you step make sure don’t hurt you self needs to do housekeeping be safe

Everyone was 6 feet from each other and had there mask on

This was a high rate dump I use to park close to the well but on this one I stayed a little bit , away from it but still on the 10 step away from working zone .. just in case the start leaking
WWD2-28.

On this well 8114C we was unable to pump, call David and he give us different well 8066c-4 the volumes were different way less than the other one, so we end up bringing back chemicals, reported to
Jeremy and that was good communication

We found a big trench open on location immediately we put some safety cones that way nobody get hurts be safe

It’s was hot 102 so pic reminded ilusión to drink water

Used the chemical suit and this weather is Danger please drinking plenty of water even and the morning the temperature is hot be safe

MTS personal talked about Trip hazards on location, discharge hose, suction hose, and ground cable to watch our steps finished the job with no insident

Still the weather is hot drinking plenty of water even if you don’t needed be safe

This is a BBS , my coworker was pulling a 50 foot hose and I see there was a rock so I can try to help him lift in the hose so he can pass by , OK without hurting his self

We MTS personal safely were all personal protective equipment during the job, steel toe boots, hard hats, impact gloves, safety glasses, and acid protective equipment

There’s a Lot of hoses on the ground while doing the coil tubing job we told everyone that was going to be around this area to be careful

We MTS personal safely we mange to rig up to well, pump the job rig down with safety in Maine

We MTS personal safely we mange to rig up to well, pump the job rig down with safety in Maine

We MTS personal safely we mange to rig up to well, pump the job rig down with safety in Maine

There’s a Lotta uneven ground so we talked about in the safety meeting to be careful where you step on

We located all the trips hazards on location good job MTS crew we have hoses/cables/metal objects

MTS as we got on location everybody turn 2 Way radios on to communicate with PIC and get as spote on location

Good job MTS crew went used the hammer make sure pull down the faceshell take care the vision

All the guys had there gloves and Face shield will working good job

MTS personal safely were all personal protective equipment during the job, face shield down when using the hammer, acid equipment went acid in progress , finish the job with no insident

Used the right gloves for the job task don’t take sort cuts be safe

Ones again work bench came handy during riging up to the well, it prevents us from stretching more than we have to

There was a lot of hoses on the ground and uneven ground and we talked about it in the safety meet to watch out where your walking

Arriving on location scanning the job location, looking for potential hazards on the ground, spot pump truck, place chalk blocks on tires and place cowns on the 4 corners of the pump truck and
continue

It was hot And everyone in the jobsite Were reminding each other to drink water good job

After job all crew we start cleaning the location lives like before we get there good job

Used the all ppe you need all the time don’t take short cuts be safe

We wasRigging up on well 3244A and there was lotta pipes on our way and I had to tell everybody don’t go over the pipes and we put some cones all the way around. We did finish the job and everything
went ok

During rig up MTS personal successfully used every precaution to minimize any insident, we set up fan to eliminate or blow away gases coming from the breaking the seal of the well

We had to stoped the job do to a leak and everyone see it so we told pic about so he can the right people to see if we can continue but they shut it down

Working today at Aera energy belridge wearing the chemical suit and all ppe is hard trying to stay cool don’t be out side be safe

Using all chemical ppe on hot water is a risk make sure drinking plenty of water be safe

On this day I Noticed on truck 122 they did put a tread haft fitting to set the lowtorke valve on it and is different wrong sise 602 and we need 1502 , I did talk to the pump operator to replace it
with the right one.

MTS personal successfully rig up to the well we use the step ladder, to rich the well, that way we're not getting on to a insident or accident, everyone goes home safe and sane

Working with c / t I noticed that they have everything set up with safety in mind, we got there, set up our safety precautions we have the safety meeting, discos safety precautions and then do the job

Veryone on the job site had there monitor up to date and clean no dirt working good

Good job today working at Aera energy belridge went some body swing the hammer at location make sure stays away be safe

All crew working at Aera energy belridge make sure drinking plenty of water be safe hot weather is danger

Safety meeting!!! Before start the job we did have a safety meeting and it was very well explain all hazards and the job went fine. Thanks to everyone who was on this job

These morning as we arrive on location the supervisor give us instructions on how to spot trucks , secure them , and then he give us the safety meeting,. Good job

Working today at teams operating after the job all crew p/u all the trash on location good job mts crew

Getting on dtr location I now that we have to wear protected equipment including the special gloves for the heat and do the work safely and sane

Working today at Aera energy belridge we doing a hot welll make sure all ways using the proper gloves for hot work by safe

We was about ready to start pumping Bac-stim , I see my coworker hooking up the hose without chemicals suits and I told him to stop he didn’t open any chemical he just hook up the hose but I I asked
him why he’s doing it and he told me that he was reading the safety data sheet and the safety data sheet recommend gloves and safety glasses only And I went to read my safety data sheet and it’s
completely corrosive and we had to wear all chemical suit and safety glasses rubber gloves

When we’re finished pumping the ammonium chloride my coworker Notes the inside the cellar it was leaking water from the pipe and it was possible 10 to 12 feet of the ground level we made the
apropiate phone calls and we take care of the leak safely.

Good safe habit always stay away went used the hammer. Be safe all the time

Working at PCEC orcutt this hill have a wild animals so everyone clean the area much posible good job every one

Used the chemical suit increases the heat body so make sure drinking plenty of water be safe

Arrive on location pic start scanning location looking for a safe place to park the pump truck and looking for hazard points, and continue doing the job safely

I observe my coworkers riging up hoses to the acid transports wearing the proper gear for the job, and include my self, we all ded good job, riging up and down

Working at Aera energy belridge today is rainy. So driving is more danger drive slow on location is the best safe manners drive safe

While we riging up wether change wind than the rain, we make sure to not to slip and fall, not to walk backwards always watching our steps

Today working at Aera lost hills look we’re you step because always the ground is not level

Today start getting hot make sure everyone drink more water and watch for snakes

Riging up I observe my coworker doing the right body position while lifting or pulling, lifting with his legs, not with his back

Riging up I observe my coworker doing the right body position while lifting or pulling, lifting with his legs, not with his back

This was myself working with the survey crew at the end of the job I star Picking cones and I pick up some of their cones, by mistake They asked to Hector and he give them back,,,

Show up on location 3 hours later do it to , two hours soak time on the job. And I found the location in good set up, they spot me back with good hands signals.

We just got done working on well and at max and we have no

We are pumping at the hill in a few days but we

Working at the power plant to contribute on the ground pollution we put plastic under the MTS trucks good mts crew

While I was pumping I noticed that there was a drip coming from the suction hose let PIC know switch to water, clean the Lane fixed the problem and continue the job

test from marcom again

test from marcom

Working at Aera energy belridge 2/17/21 we have issues with the pump pic/ myself we complete use the ppe to work safe good job

Working at Aera energy belridge I see a MTS worker went connected the hoses he used the right gloves for the job task good job by safe

While riging suction hoses I noticed that one of the hoses have a wire sticking out I put red tape on it and get it out of service

Working at crc duet the rig up/rig down I see mts workers used the 3point contact good job be safe

Working at Aera energy belridge I see a MTS people went used the hammer he had his faceshell down good job

Today driving to work site is foggy can see so I decided to pull off on a safe area and wait for 15 min be safe all the time

Third contract party on location he didn't put clamps on the house, I ask him to them on and he did put them on

Third contract party on location he didn't put clamps on the house, I ask him to them on and he did put them on

Rigging up on well, and on top of the cellar was some old wood boards, we found some new woods

Working at Aera energy belridge looks you step because the ground is not level be safe at al the time

Working at crc thums make sure you have all the time the right ppe for the work task including the chemical gloves be safe

This is a almost, did it, rig up on well before put the red tape around.

Co worker was driving with wrong placard on the truck, I told him before he live the yard make sure, the placards are right.

I think we need to make safety changes and the transports trailers we need to put chains on the fittings rack to make more secure the fittings and also the cones we need to fine a better place also
the 2x1 valves because we secure the hoses but not the valve maybe one day they going to fly down the road.

Co-worker Walk out of truck with out a hard hat, I Call he's attention , Walk back to he's truck and grab the hard hat

When we got at the island this morning we have to back up the pump truck to the second well PIC did a good job , land guide me

When we got at the island this morning we have to back up the pump truck to the second well PIC did a good job , land guide me

Working at Aera energy belridge good job MTS crew because after the job everybody p/u the trash on location and live location like before we there

Working today at Aera energy lost hills today is around 80 F. But we work around hotlines make sure drinking plenty of water be safe MTS crew

Working at Aera energy belridge are location is muddy so we need to make sure not to go on the mud look we’re you step be safe

Working today at Aera energy belridge after each job every one pick up the trash on location live the location clean munch we can good job MTS crew

Driving this morning to job site PIC communicate me by phone that there were a accident on the road, for me to take another road, it was good communication

On this job I want to Get off early because the next day I was going on vacation so I will never say that I wanted to getoff early again because that day turn to a long day..

First time in a place like this to hot, we have to be drinking water, more often to keep our self hydrated

Working at Aera energy belridge I se. All crew start pickup all the trash on location good job due housekeeping taker the habitat

MTS pump operator safely bled off pressure from the pump, so we can rigdown safely

Working at Aera energy belridge please mts crew make sure drinking plenty of water because still hot be safe

MTS personal were conducting a pressure test , low torque valve start licking we operator stop release pressure we fixed the problem continue with the job

Arrive on location, put safety tape and cones around location and fan, reposition the fan as we work around the well rigging up or rigging down

Arrive on location, put safety tape and cones around location and fan, reposition the fan as we work around the well rigging up or rigging down

Working at Aera belridge after the job everyone start pick up the trash and let location clean good job MTS crew

Working at Aera energy belridge look for pinch point and went somebody used the hammer stay away be safe

I left my hard hat on top off my pickup and my co-worker call me on the radio, to let in me know, he thought that I was leaving, but I just move out the way for him to backup

Rigging up to well a coworker put a 602 instead of 1502 tubing pin, we noticed the problem and we correct it, continue we the job

Working at Aera belrige today using all ppe and chimical suet is more hot so drink more water to avoid dehydration be safe

Driving to the next well I look at the driver side mirror, and I noticed that the hand valve was open I move to the side stop and closed it

Arrive on location , PIC successfully place safety cons and red tape and sings around equipment and well to insure that no body gets in said that area

Working today at Aera energy belridge 6 foot ladder practice I good team work had one person holding the ladder this is something that always needs to have

This is lost Hill well number 8242A-4 And our paperwork only say 8242-4 so I call David to confirm well name AERA paper work is ok

Working at Aera energy after we done the job we make i good housekeeping take care the environment

On location stepping out of the truck safety person call my attention about pipe racks on the floor close to the steps We move the truck back fixed the problem and continue the job

I was going to put my Cuadmonitor and one of my co-workers, all ready put one on.

C / t Crew they didn't have H2s monitor on chest level I asked them if they can wear it at a chest level and they did

This happens in chaffee working on well C333- my self stepping on top off the well turns slippery so. I asked to my co-worker to bring my step tool.

Working and this environment health today used extra caution high pollution and heat be safe drinking plenty of water

Pump Truck #134 was missing 2 red clips on camlocks. Had PIC correct issue by adding red clips.

This was miscommunication I guess on the email I noticed in the morning when I show up at 2:30 in the morning that we have three people when only post to have two people. I start Making some phone
calls to the sales man Dispatch and then we had to send one people home

This was in Belridge a water injector Around with three pumping units and a bunch of flow lines so when we had the safety meeting I had to talk to my Pumper and let him know that we cannot go over
the flow line so we had to go around When we was rigging up and Riggen down

MTS Pump truck drove out of DTR after the job without a PIC leading him. I coached the PIC and explained that we always need to lead the pumps out.